Product Applications Guide

Plasmine’s has a diverse portfolio of paper chemical additives to meet specific properties for any of the following grades of paper

• Packaging Grades
• Bleached Board
• Unbleached Kraft Linerboard
• Recycled Linerboard
• White Top Linerboard
• Boxboard/Cartonboard - Recycled Boxboard
• Liquid Packaging Board
• Milk Carton
• Cup Stock – Cold and Hot Medium
• Partition Board
• Tube and Core Board
• Gypsum wallboard facing
• Communication Papers
• Printing and Writing
• Copy Paper
• Inkjet Paper
• Other
• Specialty Papers
• Kraft Papers
• Recycled Papers
• Specialty and Industrial
• Release Base Sheet (liner)
• Food Wrap Papers
• Filter
• Coated Papers – C1S and C2S
• Newsprint
• Virgin
• Recycled – 100 % Old News Paper (ONP)
• Tissue and Towel
• Virgin Bleached
• Virgin Kraft
• Deinked
• Internal Sizing – Rosin (Acid Operating Conditions)
• N-750-P Fluid Size (Fortified)
• Recommended for use in high temperature wet end operating systems with a pH< 4.5 and minimum alum levels of 20 dry pounds per ton
• Primary Market – Packaging or specialty grades.
• NeuRoz 540 Anionic Dispersed Rosin Size (Fortified)
• Recommended for use in all wet end temperature ranges and a pH range from 4.0 to 6.5. Excellent product for wet end systems with a low cationic demand.
• Primary Area of Use – Bleached board and specialty papers
• NeuRoz 426 Cationic Dispersed Rosin Size (Fortified)
• Recommended for use in all wet end temperature ranges and a pH range from 4.0 to 6.5. Excellent product for recycled or Kraft linerboard.
• Primary Are of Use – Packaging and specialty paper grades.
• NeuRoz XC-7 Cationic Dispersed Rosin Size (Esterified Technology)
• Recommended for use in low temperature and high pH wet end operating conditions. Also recommended for use on dryer limited machines since the rosin melt point is lower than fortified rosin sizes.
• NeuRoz 800 Cationic Dispersed Rosin - Single component rosin sizing system that can be used with or without additional alum to obtained sizing in moderate temperature (110 to 125°F) and a pH range from 5.0 to 7.0.
• Internal Sizing – Alkyl Ketene Dimer (Alkaline Operating Conditions)
• Plasmisize 100 – Low Charge Alkyl Ketene Dimer (AKD) Emulsion
• Recommended for bleached fiber applications with a low cationic demand.
• Primary area of Use – Specialty Paper Grades
• Plasmisize 300 – High Charge AKD Emulsion
• Recommended for all Kraft and recycled packaging and specialty paper grades. Excellent product for high conductivity (>5000 mmhos) operating systems.
• Primary area of Use – Kraft or Recycled packaging grades and specialty paper grades.

Note: Plasmine has available other AKD emulsions of varying charge, promoter, and AKD content to meet all wet end and retention requirements.

• Surface Treatment
• Sizing
• Size Press – KN-500, DynaCoat S10 SMA, DynaCoat XS SAE, DynaCoat 300, DynaWax 1348, and DynaWax 1636, DynaCoat S110, DynaCoat XC and DynaCoat PD
• Calendar Stack – KN-500, DynaCoat S10, and DynaWax 1636
• Scuff Resistance - DynaWax 2247
• Inkjet Printability – DynaCoat XS, DynaCoat S10, and KN-500
• COF Reduction/ Lubricity – DynaWax 3258, DynaWax 1636,
• Dimensional Stability- KN-500, DynaCoat S10, DynaShield 400R
• Strength – PVOH, DynaCoat S10, DynaLink 200
• Optical Density – Plasmisize 300, DynaFix 100
• Water Fastness – DynaFix 100
• Release – DynaWax 1636, DynaShield 300R, DynaShield 400R. DynaWax 3258, and DynaWax 4125
• Porosity Reduction – DynaCoat CSB
• Strength (Internal Additive)
• Wet Strength – DynaStrength 9125 and 930
• Product selection is based on frequency of use and ship location.
• Dry Strength – DynaStrength 620, 810, D9860, and D9880
• Product selection is based on wet end operating conditions and chemicals additives.
• Process Aids
• Dye Fixative – DynaFix 100 cationic polymer
• Absorbency Aid – Plasmine 1450 Absorbency Aid
• Stickies Control Additive – DynaShield 1306 Deposition Control Additive
• Retention and Charge Control – L.H. 301 Cationic Polymer
• Microbial Control – Plasmitrol 16
• Yankee Dryer Protection Additives
• Plasmine has a diversified portfolio of coating and release additives for the tissue and towel industry
• Detailed machine survey is required prior to product selection